Tile and Grout Cleaning

Guide · Homeowners · 3 min read · Updated 17 November 2026

Grout Sealing vs Grout Colour Sealing: Which Do You Need?

Short answer

Clear grout sealing uses an impregnating sealer that soaks into clean grout to slow staining without changing its look, typically costing £2–£4 per m². Grout colour sealing applies a coloured coating that gives stained or patchy grout a uniform, like-new finish and stronger stain resistance, typically £8–£15 per m². Choose clear sealing if the grout cleans up evenly, and colour sealing if it stays patchy.

Grout Sealing vs Grout Colour Sealing: Which Do You Need?

Why grout needs sealing at all

Standard cement-based grout is porous, which means it absorbs liquids. Spilt coffee, cooking oil, muddy water and cleaning solution all soak in, and once they dry, the stain is inside the grout rather than on the surface. That is why freshly cleaned grout often looks dark again within months, especially in kitchens and hallways.

Sealing reduces how much the grout absorbs. It does not make grout indestructible, but it gives you time to wipe up spills before they penetrate and makes routine cleaning far more effective. Epoxy grout, which is sometimes used in commercial kitchens and modern showers, is non-porous and does not normally need sealing.

New grout should be left to cure fully before sealing, usually for the period stated by the grout manufacturer, which is often several days. Sealing too early can trap moisture and affect the finish. On an older floor, sealing comes after a deep clean and enough drying time for the joints to lose the water absorbed during cleaning, typically overnight or longer in cold, damp weather.

How clear impregnating sealers work

An impregnating sealer, sometimes called a penetrating sealer, soaks into the grout and lines the pores beneath the surface. Once cured, it repels water and oil, so stains bead up rather than soaking in. Because it sits inside the grout rather than forming a film on top, it does not change the colour noticeably, does not make the floor slippery, and lets the grout breathe.

The grout must be thoroughly clean and dry before application, because the sealer will lock in any dirt left behind. It is usually applied with a fine brush or applicator along each joint, with any excess wiped off the tiles before it dries. Most products need a few hours before light use, and longer before washing.

  • Invisible once dry, keeping the grout's natural colour
  • Reduces absorption of water, oil and spills
  • Does not form a slippery surface film
  • Typically £2–£4 per m² applied professionally
  • Reapply every year or two in busy areas

How grout colour sealing works

Grout colour sealant is a coloured coating applied directly onto clean grout lines. It bonds to the grout and sets as a durable, stain-resistant layer, covering old discolouration and giving every joint the same shade. It can return grey grout to white, make patchy grout uniform, or change the colour entirely, such as from cream to light grey.

Application is careful, detailed work. Each grout line is coated with a fine brush or applicator, and any sealant on the tile face is wiped away before it cures. Because it covers the grout rather than soaking in, the result looks very close to fresh grout. It costs more, typically £8–£15 per m², because it takes longer and the product is more expensive.

Side-by-side comparison

The table compares the two options on the points that matter most to homeowners.

FactorClear impregnating sealerColour sealant
Effect on colourNone noticeableUniform new colour
Hides old stainingNoYes
Stain resistanceGoodVery good
Guide price£2–£4 per m²£8–£15 per m²
Best forGrout that cleans up evenlyPatchy, stained or tired grout
ReapplicationEvery year or two in busy areasLonger-lasting, touch up as needed

Which should you choose?

Start with a deep clean. Once the floor is clean and dry, look at the grout in daylight. If it has come back to an even colour close to the original, a clear impregnating sealer will protect it at the lower cost. If some joints are still darker than others, or the grout has been stained by years of mopping with dirty water, colour sealing will give a far better finish.

Colour sealing is also a good choice if you simply want a different look, for example lighter grout to brighten a dark kitchen, or darker grout to hide future marks in a hallway. It is not a fix for crumbling or cracked grout, which needs regrouting first.

If you are unsure, ask for a small test area. A specialist can colour seal a short section of grout in an inconspicuous corner so you can see the shade and finish against your tiles before committing to the whole floor.

Common mistakes

The most common mistake is sealing dirty grout. Whatever is in the joints gets locked in, and you cannot clean it out afterwards without stripping the sealer. Another is applying a topical sealer meant for some other surface, which can leave a sticky or slippery film on the tiles. On commercial floors, where slip resistance matters, any product used should not reduce the grip of the surface.

Finally, do not expect sealing to last for ever. Busy kitchens, hallways and showers wear sealers down, so reapply when you notice water soaking into the grout rather than beading on top.

Also avoid walking on freshly sealed grout too soon. Follow the cure time on the product, and keep pets and rugs off the floor until it is ready.

Questions people also ask

How long does grout sealer last?

A clear impregnating grout sealer typically lasts one to two years in busy areas such as kitchens, hallways and showers, and longer in quieter rooms. A simple test is to drip water on the grout: if it beads, the sealer is working; if it darkens the grout quickly, it is time to reapply.

Can you colour seal grout without cleaning it first?

No. Grout must be thoroughly cleaned and dried before colour sealing, otherwise the coating may not bond properly and can peel or wear unevenly. A professional colour seal always starts with a deep clean, then a full drying period, before the colour is applied carefully to each joint.

Does sealing grout make tiles slippery?

A good impregnating sealer should not, because it soaks into the grout rather than forming a film on the tile surface. Problems usually come from topical coatings or from sealer left to dry on the tiles. Excess should always be wiped off the tile face before it cures.

Written and checked by the Tile and Grout Cleaning team. Read our editorial policy.

Get a free tile and grout cleaning quote

Tell us what you need and we'll come back with a clear price.

Request a quote